Volver a Kinetic Technologies

Kinetic Technologies KTA1140 Evaluation Kit

Kinetic Technologies KTA1140 Evaluation Kit was designed to demonstrate the functionality, performance, and PCB layout of the KTA1140. The KTA1140 is an IEEE 802.3af/at/bt compliant power supply controller optimized for isolated and non-isolated converter topologies. The kit features a fully assembled and tested PCB with the KTA1140 IC installed.

The KTA1140 Evaluation Kit employs the KTB1095 12V, 50W flyback topology voltage regulator. The KTB1095 integrates a gate driver for a fully synchronous output rectifier and a built-in digital isolator that can supply up to 3000VRMS isolation. The Kinetic KTA1140 evaluation board has power and signal I/O connections with an array of test points for signal observation.

Features

  • Fully supports IEEE® Std. 802.3bt
  • 90W input power level
  • Support class 0-8 for Powered Device (PD)
  • Robust Type 1, 2, 3, and 4 PSE detector with proprietary digital filtering line noise
  • Auto-adjust Maintain Power Signature (MPS) for type 1-4 PSE
  • Supports up to 5 event classification
  • 2.3A programmable DC limit
  • IEC 61000-4-2/3/4/5/6 requirements for EMC compliance
  • Exceptional EMI performance
  • Low Rds-on 100V Hot-Swap FET (typical 0.1Ω)
  • Integrated short-circuit protection
  • Over temperature protection
  • Seamless support for local power down to 9.5V
  • Supports low-power standby modes
  • 5mm x 5mm, 20 lead WQFN package
  • -40°C to 125°C operating temperature range

Applications

  • Pan, Tilt, and Zoom (PTZ), security, and web cameras
  • Voice over IP (VoIP) phones
  • Lighting and high-power wireless data systems
  • Wireless LAN access points and WiMAX terminals
  • Point-of-Sale (PoS) terminals and RFID terminals
  • Thin clients and notebook computers
  • Fiber-To-The-Home (FTTH) terminals

Kit Contents

  • KTA1140 evaluation board fully assembled PCB
  • Anti-static bag
  • KTA1140 quick start guide, printed page
  • EVAL kit box

Required Equipment

  • Power Sourcing Equipment (PSE), PoE power injector, or PoE-powered network switch that can source 48V at 60W or greater
  • Load (any of the following may be used)
    • Electronic load capable of sinking 12V at 4.17A (50W)
    • Power resistor - 2.87Ω / 50W or greater value is required
    • Actual system load that does not exceed 50W at 12V
  • CAT-5, CAT-5e, or CAT-6 RJ45 M/M ethernet cable, 1m length or shorter
  • Digital multimeters, two required, used to measure input/output voltages and currents
  • Test leads
    • One pair of banana-to-clip test leads to connect a voltmeter to the eval board VIN
    • Two pairs of banana-jack test leads to connect VO+/VO- to an electronic load and volt meter

Associated Products

Kinetic Technologies KTA1140 IEEE 802.3bt Power Switch IC

Single-chip, highly integrated CMOS solution for Power over Ethernet (PoE) powered devices.

Learn Moreacerca de Kinetic Technologies KTA1140 IEEE 802.3bt Power Switch IC View Productsrelacionado con Kinetic Technologies KTA1140 IEEE 802.3bt Power Switch IC

Kinetic Technologies KTB1095 Synchronous Flyback Controller

Isolated synchronous flyback controller with internal feedback and an integrated digital isolator.

Learn Moreacerca de Kinetic Technologies KTB1095 Synchronous Flyback Controller View Productsrelacionado con Kinetic Technologies KTB1095 Synchronous Flyback Controller

Additional Resources

Typical Test Setup

Location Circuit - Kinetic Technologies KTA1140 Evaluation Kit

Layout

Kinetic Technologies KTA1140 Evaluation Kit
Publicado: 2025-02-17 | Actualizado: 2025-02-24